사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ASTM F3218-19
Standard Practice for Documenting Environmental Conditions for Utilization with A-UGV Test Methods- 발행일 : 2019-09-01
- 발행기관 : ASTM
상세정보
| 분야 | 15.08 : 감지측정, 진공청소기, 안전 시스템 |
|---|---|
| 적용범위 | 1.1 When conducting test methods, it is important to consider the role that the environmental conditions play in the Automatic through Autonomous – Unmanned Ground Vehicle (A-UGV) performance. Various A-UGVs are designed to be operated both indoors and outdoors under conditions specified by the manufacturer. Likewise, end users of the A-UGV will be operating these vehicles in a variety of environmental conditions. When conducting and replicating F45 test methods by vehicle manufacturers and users, it is important to specify and document the environmental conditions under which the A-UGV is to be tested as there will be variations in vehicle performance caused by the conditions, especially when comparing and replicating sets of test results. It is also important to consider changes in environmental conditions during the course of operations (for example, transitions between conditions). As such, environmental conditions specified in this practice are static, dynamic, or transitional, or combinations thereof; with the A-UGV stationary or in motion. This practice provides brief introduction to the following list of environmental conditions that can affect performance of the A-UGV: Lighting, External sensor emission, Temperature, Humidity, Electrical Interference, Air quality, Ground Surface, and Boundaries. This practice then breaks down each condition into sub-categories so that the user can document the various aspects associated with the category prior to A-UGV tests defined in ASTM F45 Test Methods (for example, F3244). It is recommended that salient environment conditions be documented when conducting F45 test methods. 1.2 The environmental conditions listed in 1.1 to be documented for A-UGV(s) being tested are described and parameterized in Section 4 and allow a basis for performance comparison in test methods. The approach is to divide the list of environmental conditions into sub-conditions that represent the various aspects of the major category (for example, sunlight within ambient lighting). Where necessary, this practice also provides guidelines (for example, lighting direction) to document environmental conditions in an existing environment. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are not precise mathematical conversion to imperial units. They are close approximate equivalents for the purpose of specifying material dimensions or quantities that are readily available to avoid excessive fabrication costs of test apparatuses while maintaining repeatability and reproducibility of the test method results. These values given in parentheses are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 |
43.020 : 도로 수송 일반
35.240.60 : 수송, 무역 및 기타 분야에서의 IT 응용 |
| 페이지수 | 21 |
| Edition | 19 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F3218-19상세보기 | Standard Practice for Documenting Environmental Conditions for Utilization with A-UGV Test Methods | 2019-09-01 | 표준 |
| 2 | ASTM F3218-17상세보기 | Standard Practice for Recording Environmental Effects for Utilization with A-UGV Test Methods | 2017-07-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM F3381-19 - Standard Practice for Describing Stationary Obstacles Utilized within A-UGV Test Methods
- ASTM F3265-17 - Standard Test Method for Grid-Video Obstacle Measurement
- ASTM F3244-21 - Standard Test Method for Navigation: Defined Area
- UL 991 :2010 (3rd Edition) - UL Standard for Safety Tests for Safety-Related Controls Employing Solid-State Devices
- ISO 13849-1:2023 - Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)