한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    표준

    판매

    ASTM D6110-18

    Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
    • 발행일 : 2018-04-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 116,500원

    • [영어]PRINT 116,500원

상세정보

분야 08.03 : 플라스틱 (Ⅲ)
적용범위

1.1 This test method is used to determine the resistance of plastics to breakage by flexural shock as indicated by the energy extracted from standardized (see Note 1) pendulum-type hammers, mounted in standardized machines, in breaking standard specimens with one pendulum swing. This test method requires specimens to be made with a milled notch (see Note 2). The notch produces a stress concentration which promotes a brittle, rather than a ductile, fracture. The results of this test method are reported in terms of energy absorbed per unit of specimen width (see Note 3).

Note 1: The machines with pendulum-type hammers have been standardized in that they must comply with certain requirements including a fixed height of hammer fall, which results in a substantially fixed velocity of the hammer at the moment of impact. Hammers of different initial energies (produced by varying their effective weights), however, are recommended for use with specimens of different impact resistance. Moreover, manufacturers of the equipment are permitted to use different lengths and constructions of pendulums with possible differences in pendulum rigidities resulting (see Section 5). Be aware that other differences in machine design do exist.

Note 2: The specimens are standardized in that they have a fixed length and fixed depth, however, the width of the specimens is permitted to vary between limits. One design of milled notch is allowed. The notch in the specimen serves to concentrate the stress, minimize plastic deformation, and direct the fracture to the part of the specimen behind the notch. Scatter in energy-to-break is thus reduced. Because of differences in the elastic and viscoelastic properties of plastics, however, response to a given notch varies among materials.

Note 3: Caution must be exercised in interpreting the results of this test method. The following testing parameters have been shown to affect test results significantly: method of specimen fabrication, including but not limited to processing technology, molding conditions, mold design, and thermal treatment; method of notching; speed of notching tool; design of notching apparatus; quality of the notch; time between notching and test; test specimen thickness; test specimen width under notch; and environmental conditioning.

1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 4: This standard resembles ISO 179 in title only. The content is significantly different.

1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드
페이지수 17
Edition 18

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D6110-18상세보기 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2018-04-01 표준
2 ASTM D6110-17상세보기 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2017-12-01 구판
3 ASTM D6110-10상세보기 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2010-04-01 구판
4 ASTM D6110-08상세보기 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2008-08-01 구판
5 ASTM D6110-06상세보기 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2006-03-15 구판
6 ASTM D6110-05a상세보기 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2005-11-01 구판
7 ASTM D6110-05상세보기 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2005-07-01 구판
8 ASTM D6110-04e1상세보기 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2004-03-01 구판
9 ASTM D6110-04상세보기 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2004-03-01 구판
10 ASTM D6110-02상세보기 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 2002-08-10 구판
11 ASTM D6110-97상세보기 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 1997-07-10 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)