한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM B233-97(2012)

    Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes
    • 발행일 : 2012-10-15
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 110,700원

    • [영어]PRINT 110,700원

상세정보

분야 02.03 : 전도체
적용범위

1.1 This specification covers aluminum 1350 drawing stock 0.375 in. (9.52 mm) to 1.000 in. (25.40 mm) in diameter, in the tempers shown in Table 1, for drawing into wire for electrical conductors (Explanatory Note 1 and Note 2).

TABLE 1 Tensile Property LimitsA

Temper

Tensile Strength

ksi

MPa

1350-O

 8.5–14.0

 59–97

1350-H12 and -H22

12.0–17.0

 83–117

1350-H14 and -H24

15.0–20.0A

103–138

1350-H16 and -H26

17.0–22.0A

117–152

A Applicable to stock sizes through 0.500-in. (12.70-mm) diameter. The values to apply for larger sizes in these tempers shall be negotiated at time of inquiry.

1.2 The SI values of density and resistivity are to be regarded as the standard. For all other properties the inch-pound values are to be regarded as standard and the SI units may be approximate.

Note 1—Prior to 1975, aluminum 1350 was designated as EC aluminum.

Note 2—The aluminum and temper designations conform to ANSI H35.1. Aluminum 1350 corresponds to unified numbering system A91350 in accordance with Practice E527.
TABLE 2 Chemical RequirementsA

Element

Composition, %

Silicon, max

  0.10

Iron, max

  0.40

Copper, max

  0.05

Manganese, max

  0.01

Chromium, max

  0.01

Zinc, max

  0.05

Boron, max

  0.05

Gallium, max

  0.03

Vanadium plus titanium, total, max

  0.02

Other elements, each, max

  0.03

Other elements, total, max

  0.10

Aluminum, min

 99.50

A Analysis shall regularly be made only for the elements specified in this table. If, however, the presence of other elements is suspected or indicated in amounts greater than the specified limits, further analysis shall be made to determine that these elements are not present in amounts in excess of the specified limits.
TABLE 3 Electrical Resistivity Limits

Temper

Resistivity, Ω·
mm 2/m, max

Equivalent Volume
Conductivity,
% IACS, min

1350-O

0.027899

61.8

1350-H12 and -H22

0.028035

61.5

1350-H14 and -H24

0.028080

61.4

1350-H16 and -H26

0.028126

61.3


TABLE 4 Equivalent Resistivity Values at 20°CA

Material

Volume Conductivity,
% IACS

Resistivity Constants

Volume

Ω·mm 2/m

Ω·cmil/ft

μΩ·in.

μΩ·cm

Copper

100

0.017241

10.371

0.67879

1.7241

 

 

 

 

 

 

Aluminum

  61.3

0.028126

16.919

1.1073

2.8126

 

  61.4

0.028080

16.891

1.1055

2.8080

 

  61.5

0.028035

16.864

1.1037

2.8035

 

  61.8

0.027899

16.782

1.0984

2.7899

A The equivalent resistivity values for 100 % IACS conductivity were each computed from the fundamental IEC value (1/58  Ω·mm2/m) using conversion factors each accurate to at least seven significant figures. Corresponding values for other conductivities (aluminum) were derived from these by multiplying by the reciprocal of the conductivity ratios accurate to at least seven significant figures.
TABLE 5 Diameter Tolerances

Specified Diameter, in.
(mm)

Tolerance, in. (mm), Plus or Minus

Deviation of MeanA
Diameter from
Specified Diameter

Deviation at Any
Point from
Specified Diameter

0.375–0.500 (9.52–12.70)
0.501–1.00 (12.73–25.40)

0.020 (0.51)
0.025 (0.64)

0.030 (0.76)
0.035 (0.89)

A For this specification, mean diameter is the average of the maximum diameter and the minimum diameter measured in the same transverse plane along the length.
국제분류(ICS)코드
페이지수 4
Edition 97(2012)

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM B233-97(2021)상세보기 Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes 2021-10-01 표준
2 ASTM B233-97(2016)상세보기 Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes 2016-10-01 구판
3 ASTM B233-97(2012)상세보기 Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes 2012-10-15 구판
4 ASTM B233-97(2007)상세보기 Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes 2007-10-01 구판
5 ASTM B233-97(2003)e1상세보기 Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes 1997-03-10 구판
6 ASTM B233-97상세보기 Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes 1997-01-01 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)