한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM A684/A684M-10a

    Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled
    • 발행일 : 2010-10-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]보안PDF 135,800원

상세정보

분야 01.03 : 철강-강판, 강대 및 강선
적용범위

1.1 This specification covers cold-rolled, high-carbon strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. [7.6 mm] or less in thickness and over ½ to 2315/16 in. [12.5 to 600 mm] in width, inclusive. Strip tolerance products may be available in widths wider than 2315/16 in. (600 mm) by agreement between purchaser and supplier; however, such products are technically classified as cold-rolled sheet. The maximum of the specified carbon range is over 0.25 to 1.35 %, inclusive. It is furnished in the following types as specified:

1.1.1 Soft spheroidized annealed high-carbon steel is intended for applications requiring maximum cold forming. It is normally produced to give the lowest maximum Rockwell hardness for each grade.

1.1.2 Soft annealed high-carbon steel is intended for applications requiring moderate cold forming. It is produced to a maximum Rockwell hardness.

1.1.3 Intermediate hardness high-carbon steel is intended for applications where cold forming is slight or a stiff, springy product is needed, or both. It is produced to specified Rockwell hardness ranges, the maximum being higher than obtained for the annealed type.

1.1.4 Full hard high-carbon steel is intended for flat applications. It is produced to minimum Rockwell hardness requirements, which vary with grade, microstructure and gauge. Full hard can be produced with either a pearlitic or spheroidized microstructure or a mixture of both. The minimum hardness should be established between the consumer and the producer.

1.2 This specification is applicable for orders in either inch-pound units or SI units.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
국제분류(ICS)코드 77.140.50 : 보통 강제품 및 반제품
페이지수 10
Edition 10a

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM A684/A684M-25a상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2025-12-01 표준
2 ASTM A684/A684M-25상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2025-11-01 표준
3 ASTM A684/A684M-25상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2025-11-01 구판
4 ASTM A684/A684M-24상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2024-10-15 구판
5 ASTM A684/A684M-24상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2024-10-15 구판
6 ASTM A684/A684M-17상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2017-05-01 구판
7 ASTM A684/A684M-17상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2017-05-01 구판
8 ASTM A684/A684M-15상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2015-11-01 구판
9 ASTM A684/A684M-15상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2015-11-01 구판
10 ASTM A684/A684M-14상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2014-10-01 구판
11 ASTM A684/A684M-14상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2014-10-01 구판
12 ASTM A684/A684M-12상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2012-05-01 구판
13 ASTM A684/A684M-12상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2012-05-01 구판
14 ASTM A684/A684M-10a상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2010-10-01 구판
15 ASTM A684/A684M-10a상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2010-10-01 구판
16 ASTM A684/A684M-10상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2010-05-01 구판
17 ASTM A684/A684M-10상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2010-05-01 구판
18 ASTM A684/A684M-08상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2008-10-01 구판
19 ASTM A684/A684M-08상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2008-10-01 구판
20 ASTM A684/A684M-06상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2006-10-01 구판
21 ASTM A684/A684M-06상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2006-10-01 구판
22 ASTM A684/A684M-86(2002)상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2002-11-10 구판
23 ASTM A684/A684M-86(2002)상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 2002-11-10 구판
24 ASTM A684/A684M-86(1998)상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 1998-09-10 구판
25 ASTM A684/A684M-86(1998)상세보기 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled 1998-09-10 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)

  • PDF+PRINT :

    직접 파일 다운로드 및 인쇄본 우편발송(2~3일 소요)

  • 보안PDF+PRINT :

    직접 파일 다운로드 및 인쇄본 우편발송(2~3일 소요)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • ASME PBVC Plus :

    인쇄본 우편발송 및 온라인 구독(1User용, 2년)